منوی فروشگاه
Your Cart

اهواز هابی، اولین و بزرگترین فروشگاه قطعات رباتیک و مولتی روتور تفریحی و ورزشی در ایران

موجودی و قیمت قطعات همیشه دقیق و به روز میباشد

برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج

برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج
برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج
برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج
برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج
برد کنترل گیمبال دو محوره الکسموس BASECAM BGC3.1 به همراه سنسور زاویه سنج
3,800,000 تومان
  • وضعیت انبار: موجود
  • مدل: Gimbal main control 2axis BASECAM BGC3.1

برد کنترل گیمبال براشلس دو محوره الکسموس Basecam BGC3.1 ورژن جدید به همراه سنسور زاویه سنج MPU6050 برای ساخت انواع گیمبال و استابلایزر دوربین دو محوره دستی هند هلد و یا گیمبال پرنده های هلی شات کاربرد دارد .

توصیه میشود برای برق ورودی این گیمبال از ولتاژ رگلاتور 12 ولت استفاده شود.

 

BASECAM BGC 3.1 Control Board MOS Large Current Two-axis Brushless Gimbal Controller 

Description:
- This controller is for use with brushless direct drive (BLDC) motors. Included sensor unit with gyro and accelerometer is mounted on the camera platform; the controller unit receives data from IMU to define camera inclination angles. PID-controller calculates the amount of compensation and sends command to the power unit, which controls the current in the windings and thus the direction of the vector of magnetic field in the stator. Magnetic field moves the rotor to the right position.In 3.0 on the basis of circuit board to upgrade again, increase the stability of the board


Features:
100% Brand new and high quality!
BGC 3.0 MOS Large Current 2-axis Brushless Gimbal Controller Driver
Adopts MOS tube drive, with larger current
Two-axis brushless gimbal driver

MPU6050
Support 2-8 series gimbal motor

Specifications:
Drive mode: MOS
Size: 5*5cm
Peak current: 10A

Package included:
1* Two-axis brushless gimbal driver
1* Sensor
1* Cable

Specifications:
- USB connector (no FTDI needed)
- Stabilized VBUS (USB port)
- Pin layout optimized GND, A1 and A2 GND, multi-port, 5V
- L6234 brushless motor driver
- 2 outputs for brushless motors
- 4 receiver inputs
- 6 analog inputs
- Serial port available
- Power LED (blue)
- Small LEDs on the USB
- Dimensions 50 mm x 50 mm
- Standard MK style mounting holes 45 mm x 45 mm
- 2 instead of 4 glass diodes SOT23
- 5V better stabilized
- Shifter lever on the I2C Bus (3.3V to 5V)
- Pull reduced (for better edges)
- Bootloader and firmware of Atmega328 already flashed with the last version
- flashed Verson 3.1 firmware



نظر بدهید

توجه: HTML ترجمه نمی شود!
بد خوب
کد امنیتی

تمامی حقوق این سایت محفوظ می باشد فروشگاه رباتیک اهواز هابی © 1404 - 1390. طراحی توسط آی سبد